Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Everyone will have their private conception in relation to Installing A Bathtub.
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a new one is also a moderately tough job. If the old bathtub is easily easily accessible, the project can relocate quickly; if you need to open a wall surface to get rid of the old tub as well as place the new bath tub, the job is a lot harder. In either case, the project is within a home handyman's abilities, although you will need a helper to vacate the old bathtub and also set in the new one. See to it you have qualified yourself for the work and also are comfortable trying it. As opposed to employing a service provider to take control of a halfway-completed job, it is much better to consider utilizing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This short article will certainly assist you mount a new bath tub in your washroom if you have actually already gotten a brand-new tub as well as don't need to change the setup of your previous water system pipes.
Your tools as well as product checklist ought to consist of the following:
Getting ready for the Installment
First of all, the supporting structure supplied with the bath ought to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before proceeding to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of the two wooden boards under its feet, put the tub in the needed placement. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the bathtub up until the level reviews degree.
To install faucets, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the water and examine all joints and new pipework for leakages and tighten them if necessary. Fill up the bathtub as well as additionally examine the overflow outlet and the normal outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub ought to wait till the bath tub has actually been used a minimum of once as this will certainly settle it right into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall between the bath and the tiling, bring about difficulties with moisture and feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid reader on Installing A Bathtub, I assumed sharing that excerpt was a smart idea. Please take the time to promote this blog entry if you enjoyed reading it. Many thanks for your time. Please come visit our blog back soon.
No more waits! Report this page